Installation Guidelines for Lino Corkoleum

Glueless “Clic” Floating Floors

If the following instructions leave any unanswered questions or if additional information is required, please contact us. You must read and understand these

instructions completely before beginning installation.

Responsibility for the suitability of this

Floating Floor and accompanying products for each individual installation cannot be assumed by

the manufacture or retailer since neither has no control over the installer's proper application. Should an

individual plank be doubtful as to appearance or dimension the installer should not use this piece.

The manufacture will send replacement in a timely fashion.

Cork is a natural product. Just like wood, cork parquet tile and plank will vary in shade or pattern definition.

Also, while not as prevalent as with wood, cork is subject to the normal behavior of minor expansion during

periods of high humidity and minor contraction during periods of low humidity (usually the heating season).

With cork floating floors, expansion and contraction can be kept to unnoticeable levels by stabilizing the

building through temperature and humidity control, allowing for proper acclimatization of the product prior to

installation, and providing the recommended expansion space mentioned below.

Installation of floating floor is not recommended in bathrooms or in areas with high moisture


INSTALLATION ON CONCRETE SUBSTRATE: Floating Floor can be installed over concrete

that is above grade, on grade or below grade. Concrete substrates are required to be sound, smooth and

level. Tolerance of level must be within 1/8” in 10'. Check concrete slab for moisture with Calcium Chloride

moisture test. Moisture content cannot be more than 3 pounds per 1,000 sq. ft. per 24 hours. Fill any low

spots with Portland based leveler and scrape any high spots.

Before installing Floating Floor,

cover concrete floor with 6 mil polyethylene sheets, run up the wall 3", overlap seams 8", and tape the sheets

together. Install plank over this moisture barrier. More information on moisture testing can be obtained at Before installing floor, cover concrete floor with 6 mil

polyethylene sheets, overlap seams 8” and tape the sheets together.


Subfloor must be clean and level. Fill any low spots with appropriate filler and sand any high spots. Tolerance

of level must be within 1/8" in 10'. Subfloor must not exceed 14% moisture content (electrical resistance

method). Check basements and under floor crawl spaces to be sure they are dry and well ventilated to avoid

damage to planks caused by moisture. For buildings with crawl spaces, Natural CORK recommends use of 6

mil polyethylene sheeting as ground cover over the earth.

IN-FLOOR RADIANT HEATING SYSTEM: With radiant heat, heat source is directly beneath the flooring, so

flooring may gain moisture or dry out faster than in a home with conventional heating system. For this

installation, once slab has cured, turn heat on, regardless of season, and leave it on for at least 5-6 days

before installation. Maximum surface temperature should never be more than 85 degrees Fahrenheit (30

degrees Celsius).

FLOATING FLOOR MUST BE ACCLIMATED: Store cork flooring out of the box at job site

for a minimum of 72 hours. During storage and installation, maintain temperature and relative humidity to

level consistent to the conditions that will prevail when building is occupied. Heating or air conditioning should

be used for an appropriate length of time prior and during installation. With improper acclimation, the floor

could noticeably expand or contract after installation. Ideal conditions are 68 degrees temperature and 50-

60% humidity.

NOTE: A run of Floating Floor exceeding 30 feet in any direction will require installation of an

expansion joint. The same will be true when transitioning from one room to another.



CLIC is a revolutionary system for installing floating floors without glue. The system has a specially shaped

tongue and groove. This sophisticated and highly accurate milled shape ensures a very tight connection during

installation and beyond. The cork wear layers are cut at a slight angle and press tightly against one another

sealing the joint. As soon as the planks are installed they are under constant tension. Installing CLIC floating

floor will require slightly more pressure than non-cork glue-less systems.

Start installing the floor in one corner, preferably parallel to the longest wall and following the direction the

light falls. It is equally possible to work from left to right or right to left.

Always insert the tongue into the groove, not the other way around.

STRING LINE: Choose the longest wall that will be parallel to the plank floor. Tap a nail part way into the

old floor ½" from the wall at each end of the room. String a line between the nails ¾” above floor level. Use

this string as a guide-line for the first row of planks. The ½" space from the wall allows room for expansion.

Shuffle Floating Floor planks for best visual mix. Mix planks from various cartons to maintain

natural color and pattern variation.

FIRST ROW: Facing the guide-line, place the first plank at the left-hand end, tongue side facing wall,

starting ½” off the wall. It is necessary to remove the tongue from all planks lining the starting wall. Use ½”

spacers at the end and along the wall (2 to a plank) while keeping the planks aligned with the string. Spacers

keep planks from shifting when subsequent rows are added. Using manufacture tapping block and a

hammer, place block FLAT on floor, with the side up that is labeled: “This Side Up For Tapping On Groove”,

tap on block gently until the ends of the two planks are firmly joined, with the joint completely closed up.

Continue this process until you reach the end wall. Cut the last plank to fit allowing for a ½" perimeter

expansion space on all sides.

IMPORTANT! To do this, you will need a hammer and the SPECIAL


tapping block may result in damage to the cork wear layer. You should not attempt to knock the

CLIC joint into place with one hit. Once the two planks have “clicked” together, DO NOT tap them

again as this can cause the joint to be too tight and result in peaking.

NEXT ROWS: If the cut-off piece from the previous row is more than 10” long it can be used to start the

next row as long as end-joints between adjacent rows are always staggered by at least 10”. Firmly holding

row 1 in place, (a weight such as a full pack of planks may be helpful).

a) Position the long side of the plank to be installed at an angle of 20-30° to the plank already installed.

Move the plank to be fitted slightly up and down at the same time as exerting forward pressure.

Using the tapping block on the long edge can help to achieve the proper locking of planks.

b) With Natural CORK tapping block, use a number of smaller taps on the short edge, until the planks

click together completely.

c) In some cases, such as under door frames, the planks cannot be rotated into one another. In these

situations, the planks can be fitted horizontally. For the long edge, you should tap them together

gradually: begin tapping lightly at the corner of a plank until the join is made, then repeat the process

every 12” until the entire long edge of the plank has clicked in with the other. In order to cut around

pipes, take a drill bit with a diameter similar to the diameter of the pipe + ¼” for expansion.

LAST ROW: Usually the last row will require all planks be cut lengthwise. Measure each plank at several

places along the length to ensure a proper fit. Remember to allow a ½" expansion space along the wall side.

Use floor pull bar and mallet to click the long side of planks.

The short edge can be joined using the tapping


FINISH: One of the major benefits of using the Uniclic system is that after installation you can immediately

walk on the floor. Remove all spacer blocks. Fix the skirting board over the extended polyethylene sheeting.

Never attach skirting board to the floor itself, but allow space for the floor to expand and contract beneath the

skirting board. In order to fill in the expansion gap around pipes and any other areas not covered by trim, use

a flexible caulk.